Comments
-
Hello @pfhie, Welcome to SonicWall community. Honestly the firmware is not model specific as we have for other platforms. The only distinguishing factor is whether it is 12 or 14(number of SFP ports). So, you should be able to use any one of the SWS14-X image for your switch. I have informed this to the concerned team and…
-
Amazing. Glad I could help. Have a wonderful day!
-
Here are the commands: admin@18B169xxxxxx> config config(18B169xxxxxx)# dhcp-server (config-dhcp-server)# scope static <STATIC_SCOPE_IPV4_HOST> <STATIC_SCOPE_MAC> (add-dhcp-server-static-scope)# netmask <IPV4_MASK> (add-dhcp-server-static-scope)# default-gateway <IPV4_HOST> (add-dhcp-server-static-scope)# commit Eg: scope…
-
Hello @bernhardhenning, Welcome to SonicWall community. I can check for the exact commands and let you know. Here is the CLI reference guide with all commands. Also, I just wanted to confirm that you have a NSA 4600; as NSA 4500 is a Gen 5 device which is no longer supported. Also, the CLI commands are very different for a…
-
Hey @SuroopMC, Thanks for the heads up. We can still be on 10.15.5 though right? Thanks!
-
@dan, Thanks for letting us know. I will have the concerned team help provide some answers there! Thanks!
-
Hello @Ninad94, As of now we can either group together the WAN interfaces or the VPN tunnel interfaces (both numbered and unnumbered together). So, to achieve this you could create a VPN across the MPLS to achieve the SD WAN using the VPN tunnel interfaces SD WAN group. We have RFE filed (RFE# 2571) to achieve the…
-
Hello @Shiju_Chacko, Welcome to SonicWall community. Apple Air Play usually uses mDNS and also needs multicast for discovery process, and the article that you have referred is to allow mDNS. Could you please allow multicast using the KB below? Please enabled multicast globally and on the interface which has the AP, phones…
-
Hello @DVAaron, This feature provides a threshold on the amount of traffic that goes to the Control Plane. You can disable it or change the threshold from MANAGE | Firewall Settings | Advanced Settings and scrolling down to 'Control Plane Flood Protection' section. A high number at all times could mean that there is a lot…
-
Hello @DVAaron, Welcome to SonicWall community. Usually that destination IP is used for NetBIOS traffic. You can probably set up a packet capture and check if there are drops for TCP/UDP 137 and 138. Thanks!
-
@mrshahin, The access point settings are saved on the firewall. So, when you connect to the NSA 2600, the settings will change according to the configuration done there. But, when you plug it back to the TZ 215, it will pull up the settings done on that firewall. I would like to add though, it should be configured on the…
-
Hello @dan, Welcome to SonicWall community. Are you using this in route all mode, may be that is the reason you are losing internet access. We have a reported issue, that the local resource access is lost from Android devices and Chromebooks. Please reach out to support for the Hotfix firmware based on your model and then…
-
@RedNet, If Capture Client is already installed on a machine and it is sitting behind a zone where Client AV enforcement is turned ON, it should not ask you to install again and let you through. I remember an issue like this in the past where the connectivity to software.sonicwall.com was failing on 6.5.0.x version. But,…
-
Hello @Bernhard_Winter, Welcome to SonicWall community. Yes, this is actually already filed as an RFE (Request for feature enhancement) just a few days ago and in the preliminary initial review state. So, we are already aware of this and have the process in place to take this request ahead. For reference the RFE ID is…
-
Perfect! Glad I could help!