Larry All-Knowing Sage ✭✭✭✭
Reactions
Comments
-
NSM support failed to solve this issue so far and it's super hard to get in touch with them. Yes, to both, and among the reasons I am going to let my clients' NSM subscriptions lapse. I'm sorry that I'm agreeing with you rather than offering a solution to your problem. But that's the state of this product, as I've written…
-
I won't have anything to report on this issue until the client reactivates their outdoor WiFi system, expected to be in mid-April. Because I have to bring the outdoor unit inside to set the connection and do a firmware update, I'll try to log a support case (but I'm not inclinded to update it every 5 days so it doesn't…
-
@MitatOnge the GUI most definitely shows them. My question was: where, exactly, is that. Found it though the hunt-and-poke method, primarily because I don't normally refer to VPN as IPSec VPN. Nor did the Gen 6.5 GUI.
-
@Ajishlal these are auto-added remnants from NSM and I thought that once the main rules were deleted the objects - which now show no reference - could be deleted. I downloaded the TSR and stepped through it with EditPlus to find all references to "GMS" and, eventually, tracked it down to Network - IPSec VPN - Rules and…
-
@okisonic - no it won't. I've already had to push (more than I normally do) to get someone to act, having reported it last Friday. Today I got this acknowledgement: This issue is reported on our backend team and our backend team is working on it. No telling when anyone will figure out what's wrong.
-
@Paul_Sedor_1T - there are several ways to get this done and the Quick Guide (https://www.sonicwall.com/techdocs/pdf/tz270-370-470-series-quick-start-guide.pdf) for your device should have the preliminary steps to get you started. Detailed information about the firewall can be found here…
-
I like this part especially Note: Try accessing MSW on chrome as that is the friendly browser. Because, after all, Firefox is the vicious, stab you in the back, browser...
-
@BWC - Michael, I did a quick Google search of the string "ifWalkCb" and the first page that came up was this: Notice the name in the first bullet. Do you have ARS enabled on this device? If so, these messages are - more than likely - associated with that service (not the other one).
-
so even if it works a thorough inspection is needed THIS! So very much so! The only options I can come up with (thanks @TKWITS ) is: Have both devices up and go screen by screen through each of the functions and settings (Tip: keep one off the network to avoid major problems!) Generate a TSR from each device and use a…
-
Even after upgrading all of my clients' devices to 6.5.4.9-93n on February 6, I just discovered there is one TZ600 that has not resumed cloud backups. Time for a new case specific to the device.
-
@tcantin - the only suggestions I have: Open Firefox, clear the browser's cache (retain your cookies), close Firefox. Reopen Firefox and retry the Migration Tool.
-
@Michael_Bischof I appreciate the response. This is a TZ270W going from 5030 to 5050; there's no HA anything here. It gave me a 3 minute warning and then kept looping on the 20 second warning with the orange light on the entire time. Yesterday I learned that 3 minutes is the standard display for a reboot. But shouldn't the…
-
Suggest you read this, especially the Installation section. (And I won't even question why you could not find this document with a simple Google search...) You state you must "update" - well, if you have older versions installed, a newer one won't install even if you use the proper command line switch...
-
@admsnwl I think if you read the referenced Microsoft article, you'll see how your site either has to comply with their move to TLS 1.2 or enable a patch to allow you to continue using the legacy modes. The URL resolves to…
-
@TKWITS Yes, that is what I am using as well. However, when I put create an FQDN for *.bosch.com and another for bosch.com and add them to an Addresss Group and then add that to Default Geo, it doesn't work. That's because Bosch uses other data centers in Germany. So the client doesn't get the pop-up window - the browser…