Comments

• Hi @Medusanyc If you are using Gen5 sonicwall firewall, For enabling the legacy protocols Navigate to the Diag page. Login to the diag page: https://firewall IP/diag.html --> Navigate to Encryption Settings and follow below KB;

  in Schannel Errors after Sonicwall Upgrade Comment by Ajishlal May 2021
• Hi @Medusanyc Navigate to Firewall Settings --> Cipher Controls.

  in Schannel Errors after Sonicwall Upgrade Comment by Ajishlal May 2021
• Hi @SEBASTIAN Was your issue resolved? If so please mark the reply as the answer to help other community members find the helpful reply quickly.

  in Possible to change On-Premise Analytics IP address? Comment by Ajishlal May 2021
• Hi @KennyMathews First make sure the TP Link not configured with bridge-mode. If its bridge-mode you cannot access the TPlink from WAN. Once the Bridge-mode enable on the back-end router, all WAN traffic is handling by Sonicwall X4 interface. For accessing the X4 Wan interface from public, You would have to enable the X4…

  in Layer 3 Splice Comment by Ajishlal May 2021
• Hi @jst3751 Both are Sonicwall Syslog Format & only the difference I noticed as same as below; Default Syslog : Default Sonicwall Syslog Format you cannot do the Syslog customize. Enhanced Syslog : Enhanced Sonicwal syslog Format you can do the customize the Syslog settings. For example you can exclude SonicPoint Stats NB:…

  in Difference between Default syslog format and Enhanced Syslog Format Comment by Ajishlal May 2021
• Hi @AntonioProinfo Most probably this issue due to the ISP MTU mismatch but there are other chances also. It is well explained in below KB.

  in VPN site to site dont work before internet down Comment by Ajishlal May 2021
• Hi @Sbarrett I found below information related for the NSv HA using Azure. Does Microsoft Azure support Active/Standby High Availability without using Azure Loadbalancer? --> 6.5.4.4-44v-21-987 build(and onwards) on Gen6 and 7.0.0-R1036(and onwards) build on Gen7 supports Layer 3 High Availability in Active/Standby Mode.…

  in Is there any detailed documentation on the HA capabilities of the Azure based NSVs? Comment by Ajishlal May 2021
• Hi @satpalmatta , If you are getting 100Mbps in SOHO, that is the maximum. Better to upgrade your hardware with Gen 6 or Gen7 if you need to utilize your 500Mbps connection.

  in Not getting bandwidth throughput. Comment by Ajishlal May 2021
• Hi @Chris If you are using the SMA, Inform you admin to enable cached credentials always if available.

  in auto run Comment by Ajishlal May 2021
• Hi @MPERU99 You may have to add SonicWALL to the relay service under the google account which you trying to send from/configure in SonicWALL firewall.

  in cannot setup SMTP to gmail to send logs Comment by Ajishlal May 2021
• Hi @satpalmatta Please let us know which firewall model are you using. Total bandwidth is depend on the model also, For example if you are using SOHO, you wont even get 100Mbps throughput after enabled the security services.

  in Not getting bandwidth throughput. Comment by Ajishlal May 2021
• Hi @Chris Please follow below KB; For launch GVC during the startup;

  in auto run Comment by Ajishlal May 2021
• Hi @Rune For Saving the credentials, You must have to allow the credential caching in NetExtender client settings.

  in Enable automatic reconnect on Netextender Comment by Ajishlal May 2021
• Hi @DisaRicks Sonicwall supposed to provide ENG/GNS3 image for education / training purpose. @Saravanan @shiprasahu93 Appreciated if you could have provide E-NG or GNS3 image of the Firewall for the testing / development environment purpose.

  in Simulation on TZ-400 Comment by Ajishlal May 2021
• Hi @Rune Try the below settings in NetExtender properties.

  in Enable automatic reconnect on Netextender Comment by Ajishlal May 2021
More Comments